RELAY and/or SOLID-STATE with CAN Bus system with fourteen switching, two analogue 0-5V with CAN output and two CAN-only rotary channels. Includes AMPSEAL connector, matching loom/s and Easyfit Transmitter on an incredibly stiff 3mm carbon fibre button plate.
Fully assembled* with six solid state-switched BACKLIT pushbuttons, four of our MIL-spec calibration switches and option to add two paddleshift switches with a choice of carbon fibre levers. Uses the FIA-face protection compatible X622 plate, seen here on a 350mm wheel, and ready to bolt onto your steering wheel boss.
A revolution in wireless steering wheel controls, for kit cars and race cars.
Main Features
- 6 relay or solid-state switched backlit buttons on wireless button plate
- 2 Mil-spec 0-5V rotary switches with 0-11 discrete CAN output signals
- 2 Mil-spec 0-255 CAN signalling rotary switches
- 8 spare switched circuits, for additional control via CAN keypads and other devices
- widely-compatible CAN signalling - Plug & Play CAN Bus compatibility with Haltech, Link, ECUMaster, AiM, Syvecs, MaxxECU & more
- built-in paddle switch mounting option
- option to add relay or solid-state switched gear shift control
- designed for FIA Appendix J Article 285 face protection pad compatibility (not included)
After you place your order, we will contact you to confirm your pushbutton colour choice and layout.
*steering wheel and face pad not included and are shown for illustration purposes only.
| Kit Car Electronics paddle shifter datasheet.pdf |
|
| KCE_WirelessCAN_Kvaser_dbc.zip |
|
| KCE_WirelessCAN_ECUMaster.zip |
|
| KCE_WirelessCAN_AIM_xc1.zip |
|
| FREEWheel USB config tool Windows driver.zip |
|
| KCE_WirelessCAN_MaxxECU.zip |
|
| FREEWheel USB Configuration tool Dec 2025.zip |
|
| FREEWheel installation instructions January 2026.pdf |
|
| 10 hole button plate X622.pdf |
|
| 10 hole button plate GTX622.pdf |
|
Included
- Easyfit Transmitter, 6 pushbuttons, 4 MIL-spec calibration switches with red and/or black knobs fitted to the chosen plate
- Transmitter battery
- Motorsport pushbutton decal sheet
- Rotary decal sheet
- 14-switching channel wireless CAN-enabled Receiver (8 relay & 6 solid-state or 14 solid-state depending on variant chosen)
- USB cable
- Installation instructions
Optional
- 0.7m loom/s or pins & housing/s
- Paddle switches and carbon fibre levers
Hardware Features
- SOLID-STATE 16: Full solid-state low-side switching of 14 concurrent 600mA resistive or inductive loads, such as standard automotive relays, with built-in short circuit and overcurrent protection
- HYBRID 16: 8 Internal relays rated to 15A at 12V which can be used for high or low-side switching of loads plus full solid-state low-side switching of 6 concurrent 600mA resistive or inductive loads
ALL MODELS:
- 2 analogue output channels for wireless 0-5V control such as multimap boost switching and traction slip control
- CAN output for seamless PDM integration across all channels, compatible with all major CAN systems
- Ultimate performance from a 10ms / 100Hz broadcast rate
- Ultimate compatibility from 7 simultaneous CAN message formats (LSB, MSB and bitmasking) with free selection of base address, bus speed and identifier length
- CAN signalling from 6 pushbuttons and 4 variable outputs (2 x discrete 0-11 CAN on the analogue channels, 2 x 0-255 CAN on 3rd and 4th outputs)
- Use as momentary switches with logic handled by your PDM, or use our intuitive configuration tool to quickly convert to latching or one of our range of driving and racing output channel modes
- AMPSEAL connector(s)
- IP67-rated USB port with rubber cap
- Flame-retardant ABS plastic
- Fully conformal coated for environmental protection
- Internal 120Ohm CAN termination resistor
- 0.7m wiring loom/s, 20AWG
- 3mm carbon fibre button plate fully assembled with 6 backlit button switches and 4 Mil-spec rotary switches
- Wireless Transmitter battery life over 2 years with backlit buttons
- Unique Transmitter ID prevents cross-talk and interference
Driving Features
- Momentary
- Latching
- BlinkSTOP indicator cancelling
- BeamSTOP main beam toggle & flash
- Flash-to-Pass
- IVA fog light behaviour
- Hazards
- Wiper Latch & Intermittent
- Flash 1Hz, flash 2Hz
- Rainlight behaviour
Size & Weight
- Easyfit Transmitter: bolts straight onto your steering wheel hub and fits all standard bolt patterns on 6 x 70mm, 6 x 74mm and 3 x 50.8mm PCD steering wheels
- Easyfit Transmitter: 214 x 190 x 19-29mm, typically 220g including battery (excludes paddles)
- SOLID-STATE 16 Receiver: 86 x 55 x 35mm
- HYBRID 16 Receiver: 121 x 66 x 40mm
Plate Design
After you place your order, we will contact you and guide you through the plate design process.
We will confirm the buttonswitch colours, any decals you would like applying and how you would like the system pre-configured.
You will receive a photo of your loose-assembled plate for approval or changes and once you are completely happy with the design, we will put it into the queue for final assembly and test.
Availability & Leadtimes
We hold all our components in stock as sub-assemblies and this allows us to build quickly to your exact specification. We ask that you allow 3 working days for loose assembly of your plate and 7-10 working days for final assembly and despatch.
Shipping
See our Delivery Information here https://blinkstop.co.uk/shop/delivery
Warranty & Returns
See our Returns policy here https://blinkstop.co.uk/shop/returns
and our Guarantee policy here https://blinkstop.co.uk/shop/guarantee
