>> Due to ongoing labour actions, our carrier's shipping operations to Canada are currently suspended. We expect this restriction to be lifted on 30th June <<

Choose from HYBRID or SOLID-STATE receivers and optionally add a wireless button plate and a keypad.

Fully assembled* and configured with supplied keypad integration out of the box.

A revolution in wireless steering wheel controls, for kit cars and race cars.

Main Features

CAN signalling as standard
Two 0-5V outputs as standard
HYBRID Receiver: Eight 15A relay switched outputs with six 600mA solid-state switched outputs
SOLID-STATE Receiver: Fourteen 600mA solid-state switched outputs
Range of wireless-enabled button plates
Options to add paddle switches, Mil-spec rotary switches and backlit pushbuttons
Upgrade to carbon fibre button plate
Add a CAN keypad, configured for interoperability out of the box
Option to add a keypad PETG bezel & mount

After you place your order, we will contact you to confirm your wheel plate pushbutton colour choice and layout and keypad inserts.

*steering wheel not included and is shown for illustration purposes only.

KCE_WirelessCAN_Kvaser_dbc.zip
KCE_WirelessCAN_ECUMaster.zip
KCE_WirelessCAN_AIM_xc1.zip
KCE_WirelessCAN_MaxxECU.zip
FREEWheel 16 Configuration tool.zip
FREEWheel HYBRID 16 installation instructions.pdf
FREEWheel SOLID-STATE16 installation instructions.pdf

Included

14-switching channel wireless CAN-enabled Receiver (8 relay & 6 solid-state or 14 solid-state depending on variant chosen)
120Ohm CAN termination resistor (fitted or loose)
USB cable
Installation instructions

Optional

Easyfit Transmitter pre-assembled with pushbuttons, Mil-spec calibration switches and knobs as ordered, fitted to the chosen plate
Transmitter battery
0.7m loom/s or pins & housing/s
Motorsport pushbutton decal sheet
Rotary decal sheet
Carbon fibre button plate in lieu of acrylic button plate
BlinkMarine CAN keypad with matching quantity of key inserts & DT connector

Hardware Features

HYBRID 16: 8 Internal relays rated to 15A at 12V which can be used for high or low-side switching of loads
HYBRID 16: Full solid-state low-side switching of 6 concurrent 600mA resistive or inductive loads, such as standard automotive relays, with built-in short circuit and overcurrent protection
SOLID-STATE 16: Full solid-state low-side switching of 14 concurrent 600mA resistive or inductive loads, such as standard automotive relays, with built-in short circuit and overcurrent protection
2 analogue output channels for wireless 0-5V control such as multimap boost switching and traction slip control
CAN output for seamless PDM integration across all channels, compatible with all major CAN systems
Ultimate performance from a 10ms / 100Hz broadcast rate
Ultimate compatibility from 7 simultaneous CAN message formats (LSB, MSB and bitmasking) with free selection of base address, bus speed and identifier length
Range of driving and racing output channel modes
Re-configurable using the included FREEWheel USB programming software
AMPSEAL connector(s)
IP67-rated USB port with rubber cap
Flame-retardant ABS plastic
Fully conformal coated for environmental protection
Wireless wheelplate Transmitter battery life over 5 years with standard buttons, and over 2 years with lit buttons
Unique Transmitter ID prevents cross-talk and interference
0.7m wiring looms
Internal 120Ohm CAN termination resistor

Driving Features

Momentary
Latching
BlinkSTOP indicator cancelling
BeamSTOP main beam toggle & flash
Flash-to-Pass
IVA fog light behaviour
Hazards
Wiper Latch & Intermittent
Flash 1Hz, flash 2Hz
Rainlight behaviour

Size & Weight

Easyfit Transmitter: bolts straight onto your steering wheel hub and fits all standard bolt patterns on 6 x 70mm, 6 x 74mm and 3 x 50.8mm PCD steering wheels
Easyfit Transmitter: 176 x 154 x 19-29mm, typically 220g including battery (excludes paddles)
HYBRID 16 Receiver: 121 x 66 x 40mm
SOLID-STATE 16 Receiver: 86 x 55 x 35mm

Plate Design

After you place your order, we will contact you and guide you through the plate design process.

We will confirm the buttonswitch colours, any decals you would like applying and how you would like the system pre-configured.

You will receive a photo of your loose-assembled plate for approval or changes and once you are completely happy with the design, we will put it into the queue for final assembly and test.

Availability & Leadtimes

We hold all our components in stock as sub-assemblies and this allows us to build quickly to your exact specification. We ask that you allow 3 working days for loose assembly of your plate and 7-10 working days for final assembly and despatch.

Shipping

See our Delivery Information here https://blinkstop.co.uk/shop/delivery

Warranty & Returns

See our Returns policy here https://blinkstop.co.uk/shop/returns

and our Guarantee policy here https://blinkstop.co.uk/shop/guarantee